How To Set Moultrie Feeder Timer

MOULTRIE MFG-13448 Pro Hunter 2 Feeder Kit Pedagogy Manual

Instructions for Pro Hunter II Feeder Kit

Thanks for your purchase of a Moultrie Pro Hunter Two Feeder Kit. Delight read this sheet before operating the unit. If you should accept any questions near this product or whatsoever other Moultrie product,
please contact us at www.moultriefeeders.com/support. Permit united states to better serve you past activating your i-year warranty online at http://www.moultriefeeders.com/warranty.

CONFIGURING AND TESTING FEEDER

SET Electric current Time: Press the Programme button and SET CURRENT TIME volition appear. Press Upwardly or DOWN to set the hour, then press RIGHT to become to the minutes. Press Upwards or DOWN to set the minutes. Press the BACK button to return to the Main Menu , or press PROGRAM to proceed through the settings
Notation: The timer is capable up to 10 feed times, each 1-60 seconds each, and each can operate on any day of the calendar week where each twenty-four hours can be toggled ON/OFF.
Prepare Current Twenty-four hours: Press the Programme button until the Set Current Day screen appears. Press LEFT or RIGHT to select the electric current 24-hour interval. Press BACK to return to the Main Bill of fare, or press Programme to proceed through the settings
Set EST. FEED REMAINING: Printing the Program push button until the Est. Feed Remaining screen appears. Printing Upward or Downward to select the amount of feed you have in the feeder. Printing BACK to return to the Primary Bill of fare, or press Program to go along through the settings.
Gear up FEED TIME: Press the Programme button until the desired Feed Timer appears at the top of the screen. Press the DOWN button until the feed time is flashing. Press PROGRAM to enter edit style. Press UP or DOWN to gear up the hr. Press the Right push to go over to the minutes. Press Up or DOWN to set up the minutes. Press Program or Dorsum to return to the Feed Timer. The factory settings include two feeder times 7am and 6pm, each for 6 seconds.
Gear up DAYS OF THE Week: After setting the feed time, press Upwards so the days of the week starting time flashing. Press PROGRAM to enter edit mode. By default all days should be enabled. Printing LEFT or RIGHT to highlight the desired day. Press DOWN to disable the selected 24-hour interval. Press UP to re-enable the selected day. Once all desired days are selected, press
PROGRAM or Back to return to the Feed Timer.
Fix RUN DURATION: Printing Down and LEFT until the RUN Duration seconds are flashing. Press Plan to enter edit mode. Press Upwardly or DOWN to prepare desired feed duration. Press Plan or Back to render to the Feed Timer.
Ready MOTOR SPEED: Press Up or Downwardly until the motor speed setting is flashing at the lesser of the screen. Press Program to enter edit way. Printing RIGHT or LEFT to select the desired motor setting. Press Programme or BACK to return to the Feed Timer. When the Feed Timer is blinking at the top of the screen, printing Program or Correct to advance to the next feed
timer. Echo for all required feed times.
Exam FEEDER: Press the BACK push to reach the Main Bill of fare. Press the TEST button to enter the Examination Way. The Test duration will appear (this volition be the same as the duration equally Feed Timer 1). Press Upward or Downward to set the Exam Duration. Press Programme. Press RIGHT or LEFT to select desired motor speed. Press PROGRAM to perform examination. Afterwards a five 2nd countdown, the test volition commence.

FCC COMPLIANCE

This device complies with part 15 of the FCC Rules. Performance is subject field to the following two weather: (one) This device may not cause harmful interference, and (ii) this device must accept any interference received, including interference that may cause undesired operation.
For devices canonical nether Part 15, the user's transmission or instruction manual for an intentional or unintentional radiator shall circumspection the user most changes or modifications to the device (Section 15.21).
Note: This equipment has been tested and institute to comply with the limits for a Course B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection confronting harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Notwithstanding, there is no guarantee that interference will non occur in a item installation. If this equipment does cause harmful interference to radio or tv set reception, which can be determined by turning the equipment off and on, the user is encouraged to endeavor to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a excursion different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/Television set technician for help.

ADJUSTING FUNNEL HEIGHT

To adapt funnel height:

With a Phillips-caput screwdriver, loosen screw.
With screw loosened, apply tabs to position funnel in one of the two positions by either pushing down or upward depending on desired position.
Once the funnel is in desired position, retighten the screw with Phillips-head screwdriver. Do not overtighten.

Assemble WITH MOULTRIE QUICK-LOCK ADAPTER

55-Gallon or 30-Gallon Barrel*

Assemble Quick-Lock adapter past snapping commodities tabs in identify as shown.
Turn the metal pulsate upside down and slide the abdomen band band around perimeter and make sure that belly ring is snug confronting
the bottom structure ring as shown (Moultrie barrel merely).
Slide the bolt through the abdomen ring ring, spacer and lock washer every bit shown. Tighten nut on bolt until metal abdomen band band tabs are touching spacer on each side.
Mountain Quick-Lock adapter using (iii) 1/4" ten 1" bolts, nuts and washers provided in the pre-drilled holes (Moultrie butt merely). Or apply the Quick-Lock adapter as a template to marking and drill
the mounting holes (non-Moultrie butt).
Connect Quick-Lock feeder kit to assembled adapter as shown. *Tin can also be used on a 6.5-gallon bucket..

ASSEMBLE MOULTRIE 30-D GALLON QUICK LOCK HOPPER

Place hopper bottom apartment on the ground, and slide the three provided angled leg brackets into the hopper as shown.
Brand sure to fully insert brackets every bit far every bit yous are able to ensure the strength of the feeder
Insert 2 (2) leg sections into each of the square leg brackets. Tap leg sections into place to ensure tight fit. Flip hopper bottom associates upside-down so that all 3 (3)
legs are on the basis.

Annotation: Failure to properly secure two halves tin can consequence in leakage.
Afterward completing hopper assembly, install as many legs sections as are needed for your application.
Connect Quick-Lock feeder kit to assembled hopper as shown
Make full with corn/feed. Do not exceed 200 lbs. Install lid by aligning handles with notches in hopper top. Twist until lid rests flush confronting chapeau stop.
To install a Moultrie game camera or Feeder Power Panel (sold separately), thread included 1/4"-20 x i" Phillips-head commodities upward through pigsty in lid handle and tighten bolt. Hat will agree upward to 3 devices.